How to wear and care for your 3D-printed PLA accessories

23 de June de 2026
Broche Radia da KUBOLAB: disco de espinhos radiais em PLA branco, impresso em 3D

Does 3D-printed jewellery break? What holds up, what doesn't, and why

24 de September de 2026

How much does a 3D-printed earring weigh? The real weight chart

Every KUBOLAB earring weighs between 1.5 g and 4.9 g. For comparison: a sheet of A4 paper weighs about 5 g. The lightest earring in the collection is less than a third of that — and the heaviest, at 4.9 g, is still lighter than a sheet of paper.

This question comes up a lot, and accessory shops almost never answer it. So here are the real weights, piece by piece, measured on the finished piece. No rounding down.

Why an earring’s weight matters so much

Earrings are where weight stops being a detail and becomes the difference between wearing a piece and not wearing it. An earring hangs from a hole in thin skin, held by a single point, sometimes for twelve hours straight.

That’s why so many people have beautiful sculptural earrings sitting in a drawer: it isn’t a lack of taste, it’s that they hurt after two hours. A large-volume earring in metal easily reaches 15 or 20 g per ear, and the ear lets you know.

Weight also changes how a piece behaves in motion. A light earring follows the head; a heavy one swings, twists and pulls.

KUBOLAB earring weights, one by one

Note how to read the table: the value is per earring, not per pair. That’s the number that matters to your ear.

Piece Weight per earring
MeFuzz Earrings 1.5 g
Metaball Earrings 1.96 g
Coil Earrings 2.1 g
Slots Earrings 2.25 g
Palitos Earrings 2.4 g
Ada Earrings 2.45 g
Meduza Earrings 2.98 g
MMetaball Duo Earrings 4.9 g
MPari Dual Earrings 4.9 g
GPari Dual Earrings 4.9 g
Metaball G Earrings 4.9 g

The MeFuzz Earrings, at 1.5 g, are the lightest piece in the collection. The four 4.9 g earrings are the largest — and even they come in under the weight of a sheet of paper.

And the other pieces?

Rings

With a ring, weight matters less, because the finger carries it differently. Even so, it’s what separates a ring you forget you’re wearing from one that gets in the way when you close your hand. If you don’t know your size yet, see how to measure at home with a strip of paper.

Piece Weight
Flor Ring 5.18 g
Meduza Ring 5.66 g
Palitos Ring 5.92 g
Ada Ring 6.27 g
Rendas Ring 6.37 g
Slots Ring 6.41 g
Coqueiro Ring 6.43 g
Fulvia Ring 6.82 g
Côncavos Ring 7.8 g
Chocolate Ring 13.37 g

Brooches

With a brooch, what matters isn’t only the weight: it’s how it is distributed across the fabric. A 22 g piece concentrated on one point distorts silk; the same piece with its hold spread out doesn’t. KUBOLAB brooches are held by four magnets on each side of the fabric, which spreads the load instead of concentrating it on a pin.

Piece Weight
Radia Brooch 13.15 g
Meduza Brooch 15.4 g
Ondas Brooch 15.46 g
Nodo Brooch 16 g
MeFuzz Brooch 18.89 g
Floe Brooch 22.48 g

Necklaces

The weights below already include the clasp — it’s the weight that reaches your neck, not that of the printed piece on its own.

Piece Weight with clasp
Bones Necklace 44.82 g
Metaball Necklace 45 g
Kubos Necklace 45.3 g
Cipó Necklace 56 g
Vértice Necklace 59 g
Chunk Necklace 61 g
Ouriço Necklace 64.66 g
Coil Necklace 168 g
Supercoil Necklace 171 g

The range here is wide on purpose. The Bones Necklace weighs 44.82 g. The Supercoil weighs 171 g — almost four times as much — because it’s a piece on another scale. Neither is light in the sense of imperceptible; both are light for the volume they occupy, which is a different and more important thing.

Why the same volume in silver would weigh eight times as much

The explanation is density, and the number is simple.

  • PLA: about 1.24 g/cm³
  • Silver: 10.5 g/cm³
  • Gold: 19.3 g/cm³

A silver piece with the same volume as a 2 g PLA earring would weigh around 17 g. In gold, over 30 g. It isn’t a question of craftsmanship — it’s the physics of the material, and no design gets around it.

That number decides what can and can’t be designed. A 4 cm tall openwork geometry is wearable in renewable-source PLA and not wearable in solid metal. Lightness isn’t a bonus of the piece: it’s the condition that allows it to exist at that size.

A big piece doesn’t have to be a heavy piece

This is where the conversation stops being technical. The material wasn’t chosen to make light accessories — it was chosen to make it possible to design volume, presence and scale without the piece becoming impossible to wear.

A 2 g earring 4 cm tall takes up space, is seen from across the room and changes the face. And it disappears from the body. Those two things together are what the material allows, and that’s why it was chosen — not for the weight itself, but for what low weight frees up in design and production.

How these numbers are measured

So there’s no doubt about what the tables say:

  • It’s the weight of the finished piece, assembled, not the weight of filament used.
  • For earrings, it’s the weight per earring — double it for the pair.
  • For necklaces, it includes the clasp.
  • For rings, the value varies slightly with size: a larger ring has more material. The figures in the table are for common sizes.
  • Variations of up to about 5% between units of the same piece are normal in 3D printing.

If the weight of a specific piece is missing, just ask: studio@kubolab.com.br.

See the pieces by category: earrings, rings, brooches, necklaces — or the full collection in the shop.

✕
How much does a 3D-printed earring weigh? The real weight chart
We use cookies to keep this site working and to understand how it is used. By continuing to browse, you agree to our Privacy Policy.
Read more